compressive stress的例句大全

The mechanics behavior of membrane material under residual stress and compressive stress has been studied.

涉及力学问题有薄膜材料在残余应力和外载荷作用下的变形、应力、断裂和屈曲等.

Experiment shows, polymer polybasic alcohol can effectively enhance the compressive stress of polyamine soft foam plastic.

研究结果表明:聚合物多元醇能有效地提高聚氨酯软泡的压陷性能.

A unified numerical expression of the compressive stress-strain curve applicable to concrete is put forward.

研究了自密实混凝土在受压过程中的变形,建议了适用于受压应力 — 应变曲线的数学表达式.

When compressive stress reaches zero, a critical value of the post-peak Poisson's ratio is achieved.

当压缩应力降至零时, 峰后泊松比达到临界值.

The residual compressive stress is beneficial to fatigue strength.

表层残余压力对工件的疲劳强度起着有益的作用.

The compressive stress of general polyamine soft foam plastic is improved with polymer polybasic alcohol.

为了改善普通聚氨酯软泡的压陷性能,采用添加聚合物多元醇,并对照其添加前后的物性.

The strain rate has little effect on the compressive stress parallel to the direction of pores.

藕状多孔铜沿平行气孔方向静态压缩时应力—应变曲线受应变速率影响很小.

The research showed that there was residual compressive stress in the ceramics layers.

研究发现,叠层复合材料中陶瓷层存在较大残余压应力.

Thus, under the same bolt tension, reduce narrow smooth surface after the compressive stress will increase.

这样, 在螺栓张力相同的情况下, 缩小后的窄光滑面的压紧应力就会增大.

Destruction mechanism of rock included crack under compressive stress condition had been discussed.

探讨了含有裂隙的岩石在压缩状态下的破坏机制.

Early-age stress analysis of concrete diaphragm wall through tensile and compressive creep modeling

考虑拉伸与压缩不同徐变特征的混凝土连续墙早龄内应力分析

( b) For concrete in compression zone a stress-strain relation for repeated axial compressive cyclic loading, is adopted instead of that for reversed loading.

对混凝土受压区采用轴向重复加载的应力-应变关系而不是反复加载的。

Removing or damaging the shot-peened layer can reduce the protection that this compressive layer provides against fatigue and stress corrosion crack initiation.

喷丸压缩层的改变或损坏会降低压缩层抵抗疲劳和应力腐蚀裂纹的保护性。

The test results show that the longer the time of moist curing, the higher the values of compressive strength, splitting tensile strength, elastic modulus and critical stress intensity factor.

试验结果表明，抗压强度、弹性模量、抗拉强度以及临界应力强度因子随标准养护时间的增长而增大，弹性模量对养护条件的敏感性最大。

The maximum horizontal direction NE60~ 65 ° of principal compressive stress on Jianghan basin was given by using analytic method of measured stratigraphic dip angle in addition to borehole log data

利用钻孔测井资料并运用地层倾角测量信息分析法，给出了江汉盆地地应力最大水平主压应力方向为NE60～65°

The compressive strength and deformation tests for Lytag concrete specimens are carried out under 4 kinds of lateral stress levels and 4 stages of freeze-thaw cycle in a concrete static and dynamic tri-axial test system.

利用混凝土静、动三轴试验系统，完成了粉煤灰陶粒混凝土立方体试件在4组不同冻融循环次数、4种恒定侧压下的双轴压压强度和变形性能试验。

Ultimate stress method is presented, including stress adjusting method, compressive area method and stress and settlement decomposition method.

提出复合桩基沉降计算的最终应力法，包括简化应力调整法、压缩区域分解法和应力与沉降分解法，并给出了两个工程实例。

Rotation of whiskers and its effect on high temperature compressive flow stress of sic_w/ al-ni composite

晶须转动及其对SiC W／Al－Ni复合材料高温压缩变形流变应力的影响

Detailed analyses were performed to establish the relationships between compressive stress and strain, average infrared radiation temperature ( AIRT) and strain, average infrared radiation temperature and mechanical work of UHMWPE.

对超高分子量聚乙烯人工髋臼材料试验过程中的应力与应变、平均红外辐射温度与应变、平均红外辐射温度与机械功之间的关系进行了分析。

Actually a bending stress a combination of tensile and compressive stresses.

实际上弯曲应力是压力和张力的综合.